Best CCNA Training and CCNA Certification
and more Cisco exams log in to Certkingdom.com
QUESTION 1
Refer to the OSPF command exhibit.
Which effect does the no-summary command option have?
A. It will cause area 1 to be able to receive non-summarized inter-area routes.
B. It will cause area 1 to not receive any inter-area routes and will use a default route to reach
networks in other areas.
C. It will cause area 1 to not receive any external routes and will use a default route to reach the
external networks.
D. It will convert the NSSA area into a NSSA totally stubby area.
E. It will convert the stubby area into a NSSA.
F. It will disable OSPF auto-summary.
Answer: B
Explanation:
QUESTION 2
When troubleshooting OSPF neighbor errors, which three verification steps should be considered?
(Choose three.)
A. Verify if neighboring OSPF interfaces are configured in the same area.
B. Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
C. Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
D. Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
E. Verify if neighboring OSPF interfaces are configured with the same area type.
Answer: A,D,E
Explanation:
QUESTION 3
On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?
A. interface gi0/0/0/0
ip address 10.1.1.1 255.255.255.0
!
router ospf 1
network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0
ip address 10.1.1.1 255.255.255.0
!
router ospf 1
network 10.1.1.1 255.255.255.255 area 0
C. router ospf 1
area 0
interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0
ip address 10.1.1.1 255.255.255.0
ip ospf 1 area 0
E. router ospf 1
address-family ipv4 unicast
interface GigabitEthernet0/0/0/1 area 0
F. router ospf 1
address-family ipv4 unicast
interface GigabitEthernet0/0/0/1
area 0
Answer: C
Explanation:
QUESTION 4
Which three statements are true regarding the OSPF router ID? (Choose three.)
A. The OSPF routing process chooses a router ID for itself when it starts up.
B. The router-id command is the preferred procedure to set the router ID.
C. If a loopback interface is configured, its address will always be preferred as the router ID overany other methods.
D. After the router ID is set, it does not change, even if the interface that the router is using for the
router ID goes down. The router ID changes only if the router reloads or if the OSPF routingprocess restarts.
E. In OSPF version 3, the OSPF router ID uses a 128-bit number.
Answer: A,B,D
Explanation:
QUESTION 5
Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)
A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering
Answer: A,C
Explanation:
Best CCNA Training and CCNA Certification
and more Cisco exams log in to Certkingdom.com